How to Replace a Kia Sportage Replacement Key

For a variety of 2012 Kia Forte Key Fob models keys, the key has an integrated keyless entry system. This key is similar to a remote control, and can be exchanged by an Kia dealer.

Key fobs can fail to function due to a variety of reasons, including batteries that are dead, worn-out buttons signal interference, or water damage. Here are some suggestions to assist you in getting your Kia key fob that is a replacement for the sportage for good.

How to replace the remote key or smartkey

The battery in your Kia's intelligent key will eventually need to be replaced, whether it's a remote, a push-to-start key or a regular key that doesn't contain transponder. This is particularly in the event that your car displays a message telling that the smart or remote key is not powered by the battery.

It's a fairly simple procedure. In order to replace the battery of the key fob take the mechanical key from the slit on the back of the key fob. You then need to lift the cover. A small screw is inside the key fob to keep the battery in the correct position. Take out the old battery by removing the screw using the help of a small screwdriver. Then, insert the new one and close the slit in the key fob.

When the key fob is equipped with a fresh battery, test it by pressing the lock and unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you're required to reprogramme your key, you'll have to record the key code number on the tag for the key code.

How to replace the battery

If the Kia key fob doesn't respond to pressing the lock or unlock button, it is most likely that the battery is depleted. A weak battery can cause other issues, such as the check engine light turning on or a delay in cranking the engine. Fortunately, replacing the key fob battery is a relatively simple DIY project that requires only some basic tools.

Before you begin be sure that your vehicle is off and that all doors are closed. Find the small, metal or plastic piece on the bottom of your key fob, and gently jiggle it until the metal key slides out. You can then insert the key in the handle on the door of your driver to unlock your car.

To replace the battery on the key fob, take off the cover on the rear. Use a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery and orient the new battery to ensure that the "+" positive side is facing you, while the "negative" negative side is facing the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

Once the new battery has been installed, turn the key fob off and back on in the ignition for a few times until the door locks. Then, test your Kia key fob for kia fob to see whether it's functioning properly again.

How do I replace a smart keys

You may have either a standard keyfob or a Smart Key, based on the model of Kia Sportage. The smart key has an embedded mechanical key blade while the standard key fob does not. Both types of key fobs are equipped with batteries which eventually needs to be replaced. It is a simple process that takes less than two minutes.

Before you start, you will want to ensure that you are on a level surface with adequate lighting and that your Kia is off. Also, keep in mind that there are tiny parts inside the fob that can fall out if you are not cautious.

The small release button is located on the lower backside. It will be a circular or rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery that was in it. The new battery is a CR-2032, and can be bought through the internet or at a local auto parts store. After you've finished it should be possible to lock, unlock and start your vehicle using your key fob - even if your engine isn't running!

How do you replace the mechanical key?

The Kia keyfob is a great convenience which allows us to lock or unlock our car with just pressing a button. Like any device, the Kia key fob may have issues. Luckily, there are methods to troubleshoot these issues and ensure that our key fobs are in good working order for the long run.

A dead or weak battery is among the most common problems. This can cause the fob to stop working entirely or stop working at times. If this is the case you should replace the battery with a new one.

If this doesn't fix the issue then try using a normal flathead screwdriver to wedge open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. After opening, carefully remove the old battery and replace it with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to ensure that it's working correctly. Contact a dealer, or a locksmith to address the issue when the fob still is not working. To avoid lockouts in the future, ensure you purchase an emergency key that will be able to work with all door and trunk cylinders.